What have you done to your 2.5 gen Tundra today?

Thanks! Here are the part numbers I had for the 3 separate pieces. I actually was trying to get the Limited wood trim pieces but when it came it was the 1794 wood trim. I didn't mind though. I like the look. That's the only down side to ordering parts....there are no real pics, just drawings so you're not sure if it's the part you want sometimes.

55474-0C040-E0 Center Molding 1
55471-0C070-E0 Center Molding 1
55475-0C020-E0 Center Molding 1

 

Looks awesome! How did you do the red side panels on the doors? How did you remove the pieces?

 

What is the part number you bought for the radio surround with OEM black for 4WD? I have been wanting to do this for a while and my wife said why not. I am itching to get out, been stuck at home doing a HUGE job with my yard. The more I dig the more I find… I know stop digging

 

I have had mine in for a few years and it is working just fine, you are gonna love it. I have my GMRS antenna mounted on the top. Looks like yours has the antenna mount also

 

Nice looking rig!

 

Sent you an email with the parts information for this and the secondary intake relocations.

 

Well…got the repair estimate back. New bed, new frame. $26k in repair costs. Body shop said it’ll be 6-8 months to repair. Now I’m just waiting to hear back from insurance to see if they total it or not. This really sucks.

 

that's a bummer dude. hopefully it works out for you in the end, though.

 

Dang man. That sucks. Good luck.

 

Ugh. Brutal man. Sorry for the misfortune, hopefully you will be taken care of.

 

Dropped my truck off Monday night at my dealership. Slip and Brake lights were on, on the dash. The Brake Controller Error message in the middle. Apparently a squirrel got into my wires. On top of that I have a the cam tower leak as well.
State farm approved the claim for the re-wire ($9,346.61)
Waiting on Warranty to confirm/approve the leak (dealership estimate $2,400 roughly)
Should have the truck back by 3/17

Too make things worse, rental i was given is a ram 1500 slt with the v6 - the thing is dreadful

 

Hope so too. Just waiting on the official word from insurance.

Appreciate it!

Yeah I hope so to. This is my first rodeo dealing with an accident of this magnitude.

 

That can't be right. I'm constantly told how much better the Ram rides, how it has plenty of power, quality components, etc.

 

Yes you have to remove the pieces from the door panel, wrap it and then re-glue it all back together.

 

Isnt that more than 50% of the value? Surprised they didn't total it.

 

I have the same setup, Id skip the rear block for lift. Shackles would be better, and if you do any towing/hauling, RAS would be even better and give about an inch of lift.

 

Put my boot on...

In Park
In Drive

 

Got a shipping confirmation from @TundraTex . My VSM is inbound. Plan is to install that, new switch panel and ports, as well as plasti-dip the cup holder trim this coming weekend.

 

I reached a mileage milestone.

 

after researching viper cut fenders here is my mounting points as no one really shared how to properly secure the fenders, plastic trim while keeping the factory look/integrity.

1. use (3) factory mounting points, 1 push pin on the frame near the coil over revisor, 2 outer fender clips had to cut out center pc and remount to make room for shorter fender length).
2. drilled holes on fog lamp bracket and lower plastic liner for zip ties to pass through ( drilled hole on plastic to be close to where the brackets are for shorter zip tie lengths)
3. secure zip tie to plastic liner and metal fog lamp brackets at 3 points equal distance for better stability while driving.
4. 6 mounting point with zero play/flex and still keeping factory look and integrity

 

I like it! Link?

 

Italian leather. Choice of color, stitching style and stitching color. https://www.redlinegoods.com/Tundra07shiftboot.php/

 

Still think Gen 2.5 looks better....

 

Secondary intake pump relocation complete. Thx again to @831Tun for two parts. I managed to piece this kit together and save a few bucks over the SDHQ units.

 

Damn, I cannot believe that. So very sorry you have to go through this.

 

Looks good!
Parts breakdown on where to acquire them?

 

Looks like 2 3-4’ sections of -10 line along with two valve cover breathers from the import section at o’reilly’s and then the adapters to thread into the vacuum pumps.

 

Secondary Intake Parts

Qty 2- ICT Billet Hose Barb Fittings F10AN625BA-A (This will go into the straight ends of the hose and then into the filters.

Qty 2-Mishimoto Stainless Steel Braided Hoses MMSBH-10-4
This will be used at the pump then into the engine bay.

Qty 2- You can get a cheaper unit just be sure the inlet size is the same
K&N Vent Air Filter/ Breather: High Performance, Premium, Washable, Replacement Engine Filter: Flange Diameter: 0.625 In, Filter Height: 1.5 In, Flange Length: 0.4375 In, Shape: Breather, 62-1340

Qty 2- This is the part from 803tun. I’m sure this can be sourced through summit or earls. It would be -10an fitting male to a barbed 7/8"
This would be the first pieces into the pumps then -10 line into the engine bay.

 

Yeah! Not sure if I'm going to use GMRS... I just ordered a BF-F8HP.

 

Quite a bit cheaper than sdhq...