What have you done to your 2.5 gen Tundra today?

Installed the driver side grab handle. I got fed up dealing with trying to find a scrap one on FB marketplace and just placed an order at my local dealership Wednesday. I'm not one to underestimate an install time - it literally took me longer to go pick up the parts than it did to install them!

 

It’s not just one part number, correct? A pillar panel and grab bar need to be ordered separate?

 

Correct!

$201 62220-0C050-B0 Windshield Pillar Garnish

62220-0C050-B0 is the a pillar trim part (in gray)
74610-0C082-B0 is the handle (in gray)

Then you'll also need to run by the hardware store and pick up:
1x 1/4-20 bolt 1.5" long
1x 1/4" flat washer
1x 1/4-20 extruded u-nut washer

 

305/70/18.. about 35.3" x 12.2"

 

They're ATs surprisingly. 305/70/18. Just over 35" diameter

 

When you say “pop a lot” what do you mean? I’ve got a sound that I can’t identify.

 

Sorry, I was using the 'MTs' as abrv for Mickey Thompsons.... They look perfect on your setup!!!

 

Oh. Haha. Yeah, thanks. I'm enjoying them so far.

 

I-10 Detour while scootin across LA back to TX. Been stopping at this spot in the Atchafalaya Basin for decades to take a breath of the good things...

 

East side of the Bridge?

 

Yessir. Whiskey Bay exit north to near main river boat ramp. Old wooden bridge crossover. Worth the extra effort every single time...

 

Truck stuff. Yard work. Landscaping.

 

Installed the new Iron Bison BARDE front bumper and a good cleaning. I will say for the price I am really pleased with this bumper.

 

I have never even heard of that one before. Post side shots showing where it sits in relation to the grill surround. It doesn't look like it comes out very far.

 

@Tundra234 Yeah I found it on Extremeterrain.com and liked the clearance for bigger tires and it’s modular. Weighs right at 90 lbs. I installed Cali Raised LED Amber pods. It also has a cutout for a 30” dual row light bar behind the license plate.

 

Not bad at all. My RC bumper is about 110 lbs.

 

I almost went with that one for my front bumper as well…I have the Rough Country rear and I love it.

 

I love the front but wasn't too fond of the rear. My rear is the Road Armor Stealth.

 

Cleaned it and removed the crushed running boards after rock sliding them on CrabTree Meadows trail in VA

 

Installed my RC front coil overs. They replaced my factory strut/Toytec 3” spacer lift. On the highest clip setting (these are the adjustable M1) I got the same amount of lift even though they say 0”-2” of lift.

 

Installed the old style Pro grille. I went ahead and JB Welded the sensor to the inside of the bottom of the grille surround, following the @2020Platinum method via @Cthulhu. No issues so far.

 

I originally had the AJT kit with mine. Starting having errors after about 30 miles or so. The surround method works for moat people. I think I have only seen one or two that it didn't work for them.

 

I tried the AJT as well. Some people seem to fix the error messages by making a thinner sensor cover, but I even cut a new cover out of 1/32” (ish) piece of flat black plastic using the AJT cover as a stencil. Still got errors. Seems that every truck is a bit different. No wonder they tell everyone you’re absolutely on your own with it.

I was going to try using some washers to push the sensor forward more, but I just decided to use the rest of the JB Weld I had on hand.

 

Looks good ! ... think of upgrading that dome light, meso duel led is awesome.

https://mesocustoms.com/products/tundra-ultimate-dome-light

 

Purchased a new to me Thule surf rack setup and also a board. Sold all my boards and rack setup four years ago shortly after my son was born. Finally time to get back on the water. 8’6” 22.5” 2-7/8”. Might need to go on a couple runs so this thing can float me better

 

Let my wife drive the Tundra today while my cousin and I changed the timing belt and a drain and fill on the transmission on my wife’s 2016 accord v6. That car will be ready to go another 100k miles now with just regular oil changes.

 

Washed and cleaned it! Now to go get it dirty again.

 

Fresh oil and filter, sucked out some power steering fluid and put in red Toyota power steering fluid and finally tightened up my parking brake cable. Doesn't budge on inclines anymore.

 

Give it a couple weeks.

 

Get the fluid from your local dealer? Got a picture of it by chance?