What have you done to your 2.5 gen Tundra today?

9.5qts of fresh 0-20 and a metal oil filter cap.

 

Hopefully you meant 8.5?

 

RCI plates fully installed.




Also replaced my rear windows, since the bottom brackets that are glued to them rusted out so badly that the rear driver's window bracket fell off (thank goodness the window didn't break).

 

Nope. Started at 8.5 and didn’t measure on the dipstick. Ended up adding another qt to get it to register. Did 9qts last oil change.

 

Just an FYI, after putting the guards on I had a lot of squeaking. After removing the skids and seeing the rub marks on the hardware and guards I trimmed the guards and no more squeaking

 

Thanks for the heads up. I'll keep an ear out for any squeaking.

 

That doesnt look near as bad as i thought it was going to. I like the stock Head Unit but i kinda like that too. be nice to have an updated head unit. Looks good man!

 

Thanks! I was on the fence too, but glad I went this route instead of a flush mount one.

 

Working on a few small projects. Rago dash plate, Bulletpoint MagSafe charger (which required adding a quick-charge USB port), and front cam. Had a pretty good day considering mobility and stamina are WAY down because of a back injury - 3 herniated disks and a compressed nerve root. And feet that are extremely swollen and painful from a combination of an abnormal gait (I have to use a walker to get around) and several medications that cause swelling of the feet and ankles.

Got to the point where I just have to run the wiring for the front cam and button it up. And possibly re-flash the Maestro because the button I programmed for the front cam doesn’t seem to be working. Kind of makes me wish I had gotten the Bluetooth Maestro.

 

Finally installed the rear step. There goes the TRAIL badge. Like or dislike it, I think it matches the color of the truck.





Does not interfere with the TRD dual exhaust.


Decided to cut out the stock frame, instead of replacing it with the flimsy one provided. Since this part is discontinued by Toyota, I bought this one off of eBay for $100. Off brand, and it actually works and fits perfect.

 

Currently waiting on parts. Gas lid randomly fell off, I like the black on tan and it fits the theme of my truck so I ordered a replacement from a black truck lol should be here soon. Also backed into a tree. I’ve been having an existential crisis over getting aftermarket tails or not. I had hiRev on my 21, I’ve seen some of you guys have horror stories with the Morimoto tails, and I cannot get myself to like alpharex’ offerings. There are some stunning ones I saw here but they are $800 - valentis, I can’t get myself to pull the trigger on those though https://valentiusa.com/shop/ultra-led-tail-light-for-tundra/

 

after my lift and larger tires two years ago, I really think my 5’6” self needs one of these more and more..

 

Anyone have their tundra tuned? Had KDMAX on my Tacoma. Loved it. I’ve heard a few good things. Seeing if anyone has experience.

 

Pulled out the JBL DSP4086 amp today in preparation for my Alpine HU install (going to install it with factory setup first while I figure out my longer term plan). Managed to clip my front camera cable with the wire cutters while cutting off zip ties for the amp power wire.


So, looks like I'll be rewiring my front camera when I do the radio install...

 

The +18 offset had me going back and forth, would’ve preferred a +25 but this is close. Been on the fence of going to dirty sevens which this offset would better handle but I was just scared about needing to regear to 5.29s so I held off to 35s for now. I’ve got some BMC plates coming so I can get some of the prep work done for 37s when the time finally comes around.

 

For anyone that has cat plates on and the TRD front plate. Mine were creaking and popping and making noises when turning and going slow. My 21 Sounded like an old truck with worn out suspension. I was going to wait until the weather cooled off but decided to tackle it today. With all the plates installed, I used a sharpie to Mark the plates overlap. Then I removed all the plates except the TRD plate. I used some rubber roof scraps I had left over and glued them to the plates where they overlap. Any metal to metal now has rubber on it (including where it contracts the frame) I Put all the plates back on, and took it for a test drive, and All the noises are gone. Hopefully it won’t start to squeak now that there’s rubber on it. Stock suspension and sitting flat on the ground made it challenging but it wasn’t impossible. I will be investing in a TRD nut plate to make it easier when I need to take them off and on again.
I hope this helps anyone that has the same issue.

 

My RCI came with a similar plate, and it makes install so much easier. Highly recommend the TRD nut plate or similar.

 

Nightmare fuel right there. I swear every time I rebuild my PC and cut old zip ties I think "this will be the time..."

 

I've thought about the step for quite a while, never done it. Do you find the step a good add? It does fit right in, looks good.

 

Did not get to everything. Work in progress. Tires, rims, 3/2 leveling lift kit install this coming Wednesday. Interior trim replacement will take a while.

The LED replacement kit was surprisingly one of my favorite upgrades. Factory cabin lights are not bright enough to find dropped items in the dark, and the license plate lights and rear center brake light clear lights were not bright enough for the backup camera in the dark. Prior to this upgrade I wrongly assumed that the camera was just flip phone resolution. Now the quality is similar to a smart phones.

 

I thought it was a 3 qt spread from low to high on the dipstick, can someone confirm?

 

I thought it was a 1qt difference universally on all manufacturers?

 

I thought that too but i recall reading somewhere it was 3 for this engine. could be totally off though.

 

I just looked in the manual, i guess its 1.6 qts between low and full

 

Dang that is some super clean work! Your uncle knows what's up

 

Hoping the blatant copying (inspiration!) is well received. One of the first mod posts I saw on here. Thought it looked really good and wanted to try it out myself. First oil change was a good excuse to pull the skid plate off, and the tow hooks gave me a chance to try out my new torque wrench from Harbor Freight.

 

Rock sliders

 

I like the TRD PRO logo.

 

Thanks Jim!