Official Tundra Wheel and Tire Setups - Pics and Info

Those dont look like a -12, if they are you will rub bad with 35's

 

My info was wrong. They only make a +30 for a tundra in the phantom so that must be correct.

 

Fuel Sledge 20x10 -18mm

Ironman All Country M/T 35x12.5x20

 

Niche Scuderia 5:
22*9.5 @ +40mm
285/45R-22

Before :



After:

 

Toyo Proxes S/T III 285/60/18s on factory SR5 Alloys.

 

Finally got the lift done and the wheels/tires mounted.

2019
35x11.5/20 Nitto TG G2
FBG Coils @3" and 2" Rear Block
SPC UCA's
Anthem Defender gloss black 20X9 +18
Rubbed immediately on the front/rear mudflaps leaving the dealer. Drivers side front mud flap and fender liner already destroyed in 16 miles to get home. Removed the front/rear flaps and trimmed/tucked the front liner. There's clearance now on both sides front and rear with no rubbing at lock in forward/reverse but its damn close.

 

What do you guys think about this 20x9 with a +1 offset. I’m trying to decide if they stick out too much. I'm running 295/60/20.

 

From those 2 pictures I don’t think it looks bad. I like it

 

Looks good! Any rubbing?

 

No rubbing, The place that did the level trimmed some plastic.

 

Looks great. What lift and what size tires?

 

I'm trying to narrow down between a few Method race wheels. From what I've read at the beginning of this thread with size and lug patterns. Can someone just confirm if this is the 5x150 is the correct set up for a 10' tundra. I'm ordering the bilstein 5100 so once I figure these wheels out it just finding a tire size.

 

Yes 5x150 is what you need.

 

just a front level 2.25 inches. rear is stock. the tires are 295/60/20. the rims are 20x9 offset is +1. I didn't want them to stick out that far but it looks like Im stuck with them for now.

 

Look at mine above, i have the same tires but a +18

 

Question.
Currently I have stock Toyota wheels ( 17 x 7.5; 15MM OFFSET; 5 DOUBLE SPOKE; 6 STUD/LUG; 5.5 BOLT PATTERN; SPARKLE SILVER FULL FACE)
I have the 5100's on the top notch. My Tires are 275/70/17. I am close to the upper control arm now. I only rub at full lock in reverse once in a while.
I attached a pic.

I am wondering if these will fit? I was going to use the same tires just swap out the rims


https://www.amazon.com/Method-Race-...ZVDXV3BVZ8A&psc=1&refRID=DRGTFH6P3ZVDXV3BVZ8A


They are 17X8.5 the backspacing says 4.75
Will this work? the same as my current wheel? will it stick out more or less?

Ive been trying to figure this out and be 100% sure before I order them.

Id hate to buy rims that wont fit.

Thank you, for the help guys

 

The more negative offset, for example 0 in your wheel of choice will get u further away from uca. However, if u rub in reverse at full lock now, with more negative offset u will probably rub more. It might not be drastic though if ur current wheel has +15 offset. I can't say for certain if it will work or not. My guess is they will. U might want to ask method, or distributor. Even better, find someone running same specs methods on your gen.

 

The only place I rub is the UCA at full lock.
I have never rubbed the frame or the cab mount.
I'll try contacting Method.

 

Oh ok, then the more negative offset should help u get further away from the uca rubbing.

 

Sweet.
I contacted Method to see what they say as well.
If these wheels work out they should look great on my truck.
I was going to try to photo shop it to see how they would look. But can't do it from my crappy phone.


Thank you for your input,it's greatly appreciated

 

No problem Jerry. Just fyi theres also a wheel simulator on 1 of the wheel distributor sites, where u can see ur truck, color and all, with wheels on it. Think maybe its tire rack wheel simulator. If not, them, it is out there. Just don't remember exactly which site.

 

Got a Reply from Method Wheels




Method Race Wheels - Info
12:53 PM (28 minutes ago)


to me


Hi,

The wheels you are looking to purchase will fit and stick out a little more with the 0 offset. However your tires will rub and you would have to trim your fender wells for clearance.


Thank you,


Method Race Wheels Customer Service


Method Race Wheels | Tensor Tires

p:866.779.8604

e: info@methodracewheels.com

a:15500 Cornet Ave. Santa Fe Springs, CA 90670

w:methodracewheels.com | tensortire.com

 

See almost seems like I know what I'm talking about. Lol

 

Any way to tell how much more they would stick out ?

 

LOL
I know how dare I second guess you.

Now what are the winning lotto numbers please lol

 

There is a conversion of inches from offset. However off hand I do not know it. I'm sure you can find by looking around. Or perhaps a fellow member can help.

 

Not a good pic. 2018 crewmax, 3.5” rough country lift ( with 1/2” toytec spacers to compensate for winch/bumper ) 20x9 Ultra wheels with +25mm offset, with 35 x 12.50 x 20 toyo mt’s.

 

2013 CrewMax 4x4. 6112s up front on top setting, Built Right UCA, 5100s in the rear, 285/75/18 Toyo AT2......stock wheels for now.

 

Looking for some recommendations. I want to get new tires and wheels, but keep my truck at stock height ('16 SR5 TSS Crewmax). What offset could I get to push my tires out a little bit and what is the biggest tire I could go, without having to worry about it hitting anything and trimming? Want to get an 18" wheel. I also have the pocketed fender flares, so I'd like to get as close to even with them as I could.

Anyone else done this without a lift?

 

I've seen a couple. +18 is the norm without any rubbing with the stock 275/65's.