35x12.50r18

Anyone running this size and did not have to do a BMC? If so what's your setup (tires, wheels, suspension, etc.) Oh and pics are always very welcome. Thanks.

 

A few are. Myself included.

Icon 17" rebound 25 offset.

SPC adjustable upper control arms.

 

Running 35x12.5x17, 17x8 50mm offset with no CMC.

 

Running 35x12.5r18 M/T, stock trd pro wheels with 1.25 inch spacers. no bmc

 

35x12.5/18 Nitto Terras
Moto 0970 18" -24 offset I believe
Puts tires about 2 in outside of fenders
Put on flares to balance it all out.
4.5 BDS Lift

 

Time to upgrade. The 35X12.5s come from the factory.

 

can you post a few pictures of your setup?? I want to do the same on my pro!!

 

This is the only pic I have on my phone right now. I’ll see if I can get a couple more in a few.

 

Here's a few more. Before the flares i had about .5 inch to a full inch of tire sticking out. Let me know if these work or if you need any other pic.

Passenger full clearance, no rub turning or flexing even at full lock forward or reversing
Driver side full clearance, no rub turning or flexing even at full lock forward or reversing


Spidertrax spacer.

 

Damn! I'm after that westin outlaw front and rear bumper. I was sold on the nfab prerunner style, but when that came out. phewww....i need that!

 

Yea for sure its a nice bumper. I actually intended to get the nfab before i got the outlaw but when i saw the outlaw i liked it much better than the nfab.

 

Did your amber pods wire directly to you fog light switch in the cabin?

 

Yep have them wired to the stock connector for the fog switch in the cabin.

 

looks great! thanks for posting the pics..I think I am going to go that route but also put the CB shims in the front!

 

No problem. i have the CB shims on mine, definitely give that extra little bit of clearance. id shoot for the full CB Pro kit(shims, shackles, bumpstop extensions, and tierods) if you can, i did and no regrets on it.

 

I have everything but the shackles cause my truck is like a 1/2 low in the front.. and went with duro bumps instead of extensions! hopefully tires next week!

 

nice, did you get the 1/4 inch or 1/2 inch shims? the pro kit came with the 1/2 to give the full inch of lift on the front and the +3 shackles.

have you had any issues running the durobumps without the extensions?
i emailed durobumps before i got mine and asked if they thought it would necessary to run them or if i could remove them. they told me it'd just be best to put their bumps on the extensions if the kit came with them to avoid bottoming out, so that's how I'm running them right now.

Tires are for sure gonna change up the look of the truck. post up a pic once you get them mounted!

 

I have the 1/2 shims but have put anything on yet.. hopefully this week some time. when I talked to Duro bump they said I should not need the extension if I didn't already have then so we will see!

 

Still waiting on Coachbuilder shock shims, bumper shims, +3 shackles, steering kit and bump stop extensions and 5 BFG 35x12.5r18 KO2s

pictured are FN BFD 18x9, king OE fronts and rears, Total Chaos UCAs

I’m told that with the following alignment specs:


Alignment specs to use after installing:

Camber +.2 Degrees Per Side.

Caster +2.2 - +2.5 Degrees Per Side.

Toe +.07 - +.10 Degrees Per Side, Not to Exceed +.20 Combine.

my understanding is that everything shouldfitwith only minimal trimming. Hopefully installing this weekend. I’ll let you know how it goes.

 

Same same, planned on the nfab and even ordered it, but vendor I bought it through screwed up (not a site vendor, before I knew any better) and I canceled it and bought the westin, love it.

 

@Ryuu how do you like those tires? Been eyeing some for mine

 

What fender flares are those? They look really good!

 

I like them a lot. No issues with traction wet or dry. Wear looks good so far, seems like they'll last a good while. Biggest plus is that noise is minimal to almost none on road with it being an M/T

 

Thanks, they're the Warn 4X fender flares. Warn sources them from AirDesign

 

Are they better quality than Bushwacker? I bought the bushwacker knock offs because I’d rather pay 1/3 of the price of Bushwackers since I know they have quality issues and not feel as robbed lol. However, I like how high those Warn fit.

 

I don't know too much about ABS plastics but the 4X flares felt pretty high quality to me.
As far as bushwacker I've only seen them but never handled them, the biggest thing i didn't like about bushwacker is that every truck i saw them on the rubber molding on the edge seemed to be coming off. I thought about getting the bushwacker DRT flares but the rubber molding issue drove me away.

If you keep an eye on Amazon or 4wp they price the 4x flares down to 375-380 everynow and then but it doesn't happen too often as far as ive seen. I caught the price at like 2am on a random day.