WHAT HAVE YOU DONE TO YOUR 3RD GEN TUNDRA TODAY?

Damn! That looks very nice! I really like how the midnight multicam on the flares blends with the paint color of the truck. I am planning on putting the Pro flares on my '24 TRD OR as well. My truck is white though. I don't think it will look as good as yours, but still should look good. I also have the TRD wheels with 35"X12.50"X20" Ridge Grapplers.

 

Hard trifold worksport aluminum cover and a OEM tailpipe finisher.

 

Put some American flag stickers on. I had them on my last tundra and have always liked the look.

 

XL version, and also they are horizontally slotted, so you can adjust about an inch in-out, I mounted mine all the way out.

 

New Snow Tires Cooper Discoverer Snow Claw LT265/60/R20 E
I'm in Northeastern Vermont. Bring on the Snow!

 

Just added a badge this evening

 

I had no idea the newer 1794s had 1794 stamped on the tailgate!

 

I think it's a 1794 limited edition thing

 

Figured that as well, but just looked. Looks like the 1794 is smaller than yours and in the same location yours says, "Limited edition."

 

Before and after Eibach stage 2 pro truck lift, 20in trd wheels and 35 nittos

Blackout badges, trd pro grill (thoughts?) and will bed line the steps

 

Definitely grille change, I did mine & it's well worth it, looks much more rugged.

 

Just my opinion, but Off Road Grill > Pro Grill.

 

Wheel/tire mods make a huge difference! Looks awesome. Blackout badges will be a nice touch.

 

Looks great! Remove the steps!

 

Agree that it looks great!
Now that he's lifted it and taller tires maybe they're kinda necessary?
He did say he's gonna do bed liner on them so they'll be blacked out.

 

Had a 3 mile downhill where I didn’t have to hit the gas once. Reset the MPG and found out the max it’ll show.

 

Did you use any wheel spacers?

 

Rough Country wheel well liner.

 

5k mile service + oil change today

 

So did I.

 

Did the same yesterday. Great fit and easy to install. Hope they come out with some front ones soon.

 

But then you don’t get to see that fine TRD suspension.

EDITED: Oh, thought those were the fronts. My bad.

 

I can’t decide if the wheel well liners would be better or worse when it comes to wintry slush and salt. Might keep it away from things, might also make it harder to get rid of.

 

What a odd thing to do……here is mine

 

Went to put on a Toyota bed cover and found the Q/C is not what it use to be. The mounts were not correctly drilled on one side and the clip came broken. So it’s on while I wait for a replacement from Toyota.

 

Installed the Toyota hood deflector yesterday and had the comfort plus system installed, aka Toyota branded defa. Kit includes, block heater, trickle charger and an incab 1000w heater. Tested it out the last couple nights wow, it’s nice to wake up get in the truck and not have to idle the truck for 20-30mins. Luxury expense I know, but. Not having to idle the truck on those -30celsius mornings is going to be amazing , plus it’s significantly cheaper to run then idling. Pays for itself if I recall from my math in 2 years.

 

No spacers!

 

Do they replace the oem ones go in top?

 

No, yo remove the two clips on top i fits over the small liner. Then you put two new clips back on top, a two 10 mm bolts, one fryont and rear. There are already grommets for the screws. It’s almost like if Toyota knew there would be aftermarket parts and prepped for them.

 

Most time consuming part of the job was getting the white sticky platic of the plastic bag holding the parts and install instructions off the inside of one of the liners. Otherwise it is a 10 minute installation.